Multipoint Lock With Latch, Deadbolt And Top/Bottom Locking Rods

This option is possible only on primary swing door.

Includes top and bottom Polyamide capped locking rods, deadbolt, a Schlage compatible lock set with lockable latch and lever handles on the inside and outside. Depression of handles withdraws latch.

Lifting of handles engages rods and turn of key or thumb turn engages deadbolt and operates lock.

Operable from inside and outside.

Deadbolt Lock

Possible only on primary or secondary swing panel.

Pull handles on both sides with deadbolt(s) operated by a lockset. Lockset option of having key operations on both sides. With a profile cylinder, panel is lockable with a thumbturn from the inside and a key from the outside. To keep the panel from being blown open, this option should be used with a door closer, but note that a door closer is not possible on a swing panel in a folding system that is not attached to a side jamb.

With Multi Point Locking with Latch, Deadbolt and Top/Bottom Locking Rods

Solid brass lever handles and escutcheon plates.

Use Of Handles and Escutcheon Plates From Other Suppliers

Although availability may be restrictive and limited, other compatible handles and escutcheon plates can be used in place of the handles and escutcheon plates provided with the units. If other escutcheon plates are planned to be used, Nana Wall Systems must be notified when placing an order.

With Multi Point Locking with Latch, Deadbolt and Top/Bottom Locking Rods

In place of standard lever handles on the swing panel, any European specification lever handle with an 8 mm (5/16”) spindle can be used. However, only escutcheon plates with the following specifications can be used:

The base width must be less than 1 1/4" (32 mm).

The distance between the center of the spindle hole and the center of the lockset must be the European standard of 3 5/8" (92 mm).

For escutcheon plates that are attached with screws from the inside to the outside, the trim plate length must be such that the distance between the center point of the two screw holes is at least 7 7/8" (200 mm).

With Two Point Locking

Inward Opening Units:

In place of standard handles that operate the two point locking, any European specification window handle with a 7 mm (9/32”) spindle can be used, provided that the rosette base is less than 1 1/4" (32 mm). Note, however, that the folding stack may not be as flat a stack as with NanaWall^® standard handles.

Outward Opening Units:

In place of standard handles that operate the two point locking, only a European specification window handle with a protrusion of less than 3/4” (19 mm), with a 7 mm (9/32”) spindle, and with a rosette base of less than 1 1/4" (32 mm) can be used.

For more information on compatible hardware, contact the following companies.

Company	Address	Phone	Fax
Hoppe North America, Inc.	205 East Blackhawk Drive Fort Atkinson, WI 53538	(920) 563-2626	(920) 563-4408
Bouvet	540 DeHaro Street San Francisco, CA 94107	(415) 864-0273	(415) 864-2068
FSB	55 Ferris Street Brooklyn, NY 11231	(718) 625-1900	(718) 625-1930
Hewi, Inc.	2851 Old Tree Drive Lancaster, PA 17603	(717) 293-1313	(717) 293-3270
Omnia Industries, Inc.	P.O. Box 330 Cedar Grove, NJ 07009	(800) 310-7960	(973) 239-5960
Rocky Mountain Hardware	1030 Airport Way P.O. Box 4108 Hailey, ID 83333	(888) 788-2013	(208)788-2577
Valli & Valli(U.S.A.) Inc.	150 E. 58th, 4th FL New York, NY 10155	(877) 326-2565	(212) 326-8816

Please note that most of the catalogs of the above companies do not show matching window handles. As these handles are not common usage here, they are not stocked in the U.S.. However, as most lever handles do have matching window handles available in Europe, matching handles can usually be specially ordered.