Downloads
PART 1 - GENERAL
1.01 Summary
A. Section Includes: Manually operated top supported hinged panel aluminum and glass door system, including aluminum rails, top track, center pivot hinged panels, paired panels, single action door panels, folding/swinging hardware, locking hardware, sealing brushes, glass and glazing; designed to provide an opening glass wall, with sizes and configurations as shown on drawings and specified herein, with NanaWall FSW75, the Frameless Folding System as supplied by Nana Wall Systems, Inc.
1.02 References
A. American Architectural Manufacturers Association (AAMA):
1. AAMA 611, Voluntary Specification for Anodized Architectural Aluminum.
2. AAMA 2603 and AAMA 2604, Voluntary Specifications, Performance Requirements and
Test Procedures for Pigmented Organic Coatings on Aluminum Extrusions and Panels.
B. American National Standards Institute (ANSI):
1. ANSI Z97.1, Safety Performance Specifications and Methods of Test for Safety Glazing Material Used in
Buildings.
C. Consumer Product Safety Commission (CPSC):
1. CPSC 16CFR-1201, Safety Standard for Architectural Glazing Materials.
D. American Society for Testing and Materials (ASTM):
1. ASTM C 1036, Specification for Flat Glass
2. ASTM C 1048, Specification for Heat-Treated Flat Glass
3. ASTM E 330, Test Method for Structural Performance of Exterior Windows, Curtain Walls, and Doors by Uniform Static Air Pressure Difference.
1.03 Submittals
A. Product Drawings: Indicate dimensioning, number of panels and location of swing panels in elevation and plan views, vertical and horizontal cross section details, type of glazing material, type of hardware, and handle/knob height on panels (if any).
B. Product Data: Supplier’s literature and Owner’s Manual with installation instructions.
C. Contract Closeout Submittal: Submit Owner’s Manual from supplier. Identify with project name, location and completion date, and type and size of unit installed.
1.04 Quality Assurance
A. Supplier: Provide complete, precision built, engineered, pre-fitted unit by a single source supplier with at least 25 years of experience in the sale of folding/sliding door systems for large openings in the North American market.
B. Wind Loads: On exterior applications, if requested, design and size components to withstand dead loads and live loads caused by positive and negative wind loads acting normal to plane of wall, including building corners.
1. Design Wind Load: As calculated, by project engineer, in accordance with applicable code, as measured in accordance with ASTM E 330.
2. Deflection: Limited deflection to flexure limit of glass with full recovery of glazing materials.
C. Installer Qualifications: Installer experienced in the installation of supplier’s products or other similar products for large openings. Installer to provide reference list of at least 3 projects of similar scale and complexity successfully completed in the last 3 years.
1.05 Warranty
A. Provide supplier’s standard warranty against defects in materials and workmanship.
B. Warranty Period: Ten years for roller assemblies. For all other components, one year
(two years if unit is installed by Supplier’s certified trained installer) from date of delivery by supplier.
1.06 Site Conditions, Delivery, Storage and Handling
A. In addition to general delivery, storage and handling requirements specified in Section 01600, comply with the following:
1. Deliver materials to job site in sealed, unopened cartons or crates. Protect units from damage. Store material under cover, protected from weather and construction activities.
PART 2 - PRODUCTS
2.01 Supplier
A. NANA WALL SYSTEMS, INC.
100 Meadowcreek Drive, Suite 250, Corte Madera, CA 94925
Toll Free (800) 873-5673
Telephone: (415) 383-3148
Fax: (415) 383-0312
Website: www.nanawall.com
Email: info@nanawall.com
2.02 Materials
A. Tracks and Panels:
1. Provide aluminum head track. Finish to be clear anodized
[OR dark bronze anodized] [OR black anodized]
[OR brushed anodized]
[OR select from range of RAL high gloss powder coated finishes available from supplier] [OR select from range of RAL matte powder coated finishes available from supplier]
[OR custom color].
Two part extruded aluminum profile or steel track not allowed.
2. Provide aluminum bottom guide track. Finish to be clear anodized
[OR dark bronze anodized].
3. For all panels, provide top rails with height of 3 15/16” (100 mm)
[OR in 3/16” (5 mm) higher increments from 5 1/4” (133 mm) to 7 13/16” (198 mm)] [OR 10” (254 mm)].
4. Provide bottom rails for panels with height of 3 15/16” (100 mm)
[OR in 3/16” (5 mm) higher increments from 5 1/4” (133 mm) to 7 13/16” (198 mm)] [OR 10” (254 mm)]
[OR add 4 5/8” (117 mm) chamber bottom rail, an alternate to meet ADA swing door requirements].
5. Aluminum finish on face of top and bottom rails: Clear anodized
[OR dark bronze anodized] [OR black anodized]
[OR brushed anodized]
[OR stainless steel satin brushed cladding] [OR stainless steel polished cladding]
[OR polished brass cladding] [OR satin brass cladding]
[OR select from range of RAL high gloss powder coated finishes available from supplier] [OR select from range of RAL matte powder coated finishes available from supplier]
[OR for greater corrosion resistance, post assembly clear anodized] [OR custom finish].
6. Provide aluminum end caps that enclose the top and bottom rails: Finish to be closest match to rail finish.
7. Edges of top and bottom rails to be flat for all panels.
8. Aluminum Extrusions: Alloy specified as AIMgSi0.5 with strength rated as 6063-T5 or F-22 (European
Standard). Anodized conforming to AAMA 611, powder coated conforming to AAMA 2603 [or AAMA 2604 for select colors].
9. Panels: Panels hinged off the side jamb are available with a minimum of 1 panel and a maximum of
6 panels from either the right and/or the left side of the opening. For even larger widths, an option of unlimited floating panels are offered in 2 or 4 panel increments.
B. Glass:
1. Provide panels with standard one lite of glass. Exposed edges: Flat polished/ground.
2. Provide supplier’s standard glass 1/2” (12 mm) tempered
[OR 1/2” (12.76 mm) laminated]
[OR low iron, decorative, acrylic, wooden, stainless steel mesh as selected].
3. Glass to be clamp installed for equal distribution of weight. The edge clearance of the glass for the top rail should be no more than 1/8” (3 mm) and bite should be at least 7/8” (22 mm).
To reduce glass stress, systems with glass installed with bolts only, not allowed.
4. All glass to comply with safety glazing requirements of ANSI Z97.1 and CPSC 16CFR 1201 and requirements of ASTM C 1036 and ASTM C 1048.
C. Carrier Hardware:
1. For each pair of folding panels, provide one supplier’s proprietary unidirectional sliding panel carrier that is attached to the panel with a stainless steel cast shoe and a stainless steel ball bearing axle. Carriers to be with 4 glass fiber reinforced polyamide wheels with memory effect and polyamide bumpers to avoid metal on metal contact for quiet and smooth operation.
Metal on metal contact between top track and carriers not allowed.
2. Maximum carrying capacity of one carrier on a panel to be 330 lbs (150 kgs).
3. Adjustment: Provide system capable of specified amount of adjustments without removing panels from tracks.
D. Hinge Hardware:
1. Provide top and bottom rail with concealed 2-part hinge with stainless steel hinge pin, 2 set screws for security, and equal distribution of weight carried by 2 encapsulated axial grooved ball bearings.
E. Locking Hardware - General:
Specifier’s Note: From E 1-3, select the paragraphs that apply and delete the paragraphs not required.
1. Between each pair of folding panels provide quick release floor bolt with spring loaded security feature
[OR floor bolt with half cylinder with key operation inside].
Specifier’s Note: Floor bolt with half cylinder is recommended when panel operation control is needed.
2. All locking to be standard Schlage compatible lock set
[OR locking to be a SFIC (small format interchangeable core) up to seven pin compatible] [OR as selected].
3. If there are more than one profile cylinders on the units for the project, keyed alike
[OR keyed differently].
F. Locking Hardware for Primary or Secondary Swing Panel:
1. Provide supplier’s floor bolt with full profile cylinder that is key operated from either side
[OR floor bolt with half cylinder with key operation inside or outside]
[OR floor bolt with profile cylinder with key operation from outside and a thumb turn on the inside]. [OR quick release floor bolt with spring loaded security feature]
[OR additional locking bolt with crank handle at the top rail for additional security] [OR combination of choice].
Specifier’s Note: Depending on handle selection for Primary swing panel, locking to be at handle height or on bottom rail.
G. Handles on Primary Swing Panel:
1. Provide supplier’s standard lever handles on both sides with latch in a silver anodized finish (no lock set)
and matching strike plate on opposite panel (or secondary swing panel) to be located at handle height
[OR supplier’s standard lever handles with latch and lock set with lockable dead bolt and matching strike plate on opposite panel (or secondary swing panel)]
[OR supplier's standard lever handles with locking hardware (no lock set) and options selected from E2] [OR prepared for lever handles by others (Specifier’s Note: please provide template for holes and cut outs
needed in glass)].
H. Hardware on End Single/Double Action Panel:
1. Provide offset pivot hinged panel that can swing 180° [OR single/double action panel with center pivot point].
2. Provide without door closer
[OR bottom door closer].
3. Provide standard bottom rail locking as selected from E 1 - 3 only
[OR additional locking bolt with crank handle at the top rail for additional security].
I. Handles on End Single/Double Action Panel:
1. Provide supplier’s standard push/pull handles on both sides in brushed stainless steel finish with two point fixing and length of 11 13/16” (350 mm) and locking located at bottom rail
[OR supplier’s push/pull handles on both sides in brushed stainless steel finish in custom sizes]
[OR Tubo100 push/pull handles on both sides in brushed stainless steel finish with locking at handle height]
[OR supplier’s standard lever handles on both sides with latch in a silver anodized finish (no lock set) and matching strike plate on opposite panel (or secondary swing panel) to be located at handle height]
[OR supplier’s standard lever handles with latch and lock set with lockable dead bolt and matching strike plate on opposite panel (or secondary swing panel)]
[OR supplier's standard lever handles with locking hardware (no lock set) and options selected from F2] [OR prepared for lever handles by others (Specifier’s Note: please provide template for holes and cut outs
needed in glass)]
[OR standard panic device]
[OR no handles but with pull knob] [OR no handles and no knob].
2. For panels with push/pull handles, knobs, or panic devices provide handle height centered at 41 3/8” (1050 mm) from bottom of the panel
[OR as specified].
J. Other Components:
1. Sealing: Provide adjustable sealing brush for outside of top rail
[OR adjustable sealing brush for both sides of top rail] Provide no brushes at bottom rail
[OR spring loaded sealing brush for outside of bottom rail]
[OR spring loaded sealing brush for both sides of bottom rail].
Specifier’s Note: Standard sealing is adjustable brush for outside of top rail. Additional sealing to be determined by weather and/or acoustical requirements.
2. Bumpers: Provide recessed soft polyamide bumpers on one end of sliding panel end caps at the top and bottom to avoid metal to metal or glass to glass contact.
2.03 Fabrication
A. Use aluminum frame and rail profiles, folding hardware, locking hardware and handles, glass as specified herein to make a center pivot folding glass wall. Factory preassembled as is standard for supplier and ship with all components and installation instructions.
B. Sizes and Configurations: See drawings for selected number and size of panels, location of end and sliding single/double action panels, and location of tracks and stacking bays.
2.04 Accessories (Edit for project requirements.)
A. Provide matching frameless single track sliding HSW75 as per drawings provided. B. Provide matching frameless center pivot folding CSW75 as per drawings provided. C. Provide other single or double doors as per drawings provided.
D. Provide matching sidelights as per drawings provided.
PART 3 - EXECUTION
3.01 Erection
A. Because of the large dimensions involved and the weight and movement of the panels, verify the structural integrity of the header such that the maximum deflection with live and dead loads is limited to be the lesser of L/720 of the span and 1/4” (6 mm). Similar structural support is needed for the stacking bay(s) and any upper track leading to it. Structural support for lateral loads such as forced entry, etc. must be provided.
It is recommended that all building dead loads be applied to the header prior to installing the unit. If so and if a reasonable amount of time has been allowed for the effect of this dead load on the header, then only
the building's live load can be used to meet the above requirements of L/720 or 1/4” (6 mm). If not, both the dead and live loads need to be considered.
B. Examine surfaces of openings and verify dimensions; verify rough openings are level, plumb, and square, with no unevenness, bowing, or bumps on floor, not only in the rough opening area but also in the single action panel swing areas.
C. Installation of units constitutes acceptance of existing conditions.
3.02 Installation
A. Install frame in accordance with supplier’s recommendations and installation Instructions.
B. Installer to provide anchorage devices and to securely and rigidly fit top head track in place, level, straight, plumb and square. Install frame in proper elevation, plane and location, and in proper alignment with other work.
C. Install panels, handles and lock set in accordance with supplier’s recommendations and installation instructions.
D. If necessary, adjust hardware for proper operation.
END OF SECTION
DISCLAIMER: Nana Wall Systems, Inc. takes no responsibility for product selection or application, including, but not limited to, compliance with building codes, safety codes, laws, or fitness for a particular purpose.
The guide specifications is not intended to be verbatim as a project specification without appropriate modifications for the specific use intended and the particular requirements of a specific construction project.