Part 1 - General
1.01 SUMMARY
A. Section Includes: Engineered sliding/folding aluminum and glass door system, including aluminum frame, threshold, panels, sliding/folding and locking hardware, weather stripping, glass and glazing; designed to provide an opening glass wall, with sizes and configurations as shown on drawings and specified herein, NanaWall SL60, Thermally Broken Aluminum Framed Folding System as supplied by NANA WALL SYSTEMS, INC.
1.02 REFERENCES
A. American Architectural Manufactures Association (AAMA):
1. AAMA 611, Voluntary Specification for Anodized Architectural Aluminum.
2. AAMA 2604, Voluntary Specifications, Performance Requirements and Test Procedures for Pigmented Organic Coatings on Aluminum Extrusions and Panels.
3. AAMA 1304, Voluntary Specifications for Forced Entry Resistance of Side-Hinged DoorSystems.
B. American National Standards Institute (ANSI):
1. ANSI Z97.1, Safety Performance Specifications and Methods of Test for Safety Glazing Material Used In Buildings.
C. American Society for Testing and Materials (ASTM):
1. ASTM E 283, Test Method for Rate of Air Leakage through Exterior Windows, Curtain Walls, and Doors by Uniform Static Air Pressure Difference.
2. ASTM E 330, Test Method for Structural Performance of Exterior Windows, Curtain Walls, and Doors by Uniform Static Air Pressure Difference.
3. ASTM E 547, Test Method for Water Penetration of Exterior Windows, Curtain Walls,and Doors by Cyclic Static Air Pressure Differential.
4. ASTM E 331, Standard Test Method for Water Penetration of Exterior Windows, Skylights,Doors, and Curtain Walls by Uniform Static Air Pressure Difference.
D. Consumer Product Safety Commission (CPSC):
1. CPSC 16CFR-1201,Safety Standard for Architectural Glazing Materials.
E. National Fenestration Rating Council (NFRC):
1. NFRC 100, Procedure for Determining Fenestration Product Thermal Materials.
2. NFRC 200, Procedure for Determining Solar Heat Gain Coefficient.
3. NFRC 400, Procedure for Determining Fenestration Product Air Leakage
1.03 SUBMITTALS
A. Detail Drawings: Indicate dimensioning, direction of swing, configuration, swing panels, typical head jamb, side jambs and sill details, type of glazing material, and handle height.
B. Product Data: Manufacturer’s literature including independently tested data listing performance criteria and Owner’s Manual with installation instructions.
C. Contract Closeout Submittal: Submit Owner’s Manual from manufacturer. Identify with project name, location and completion date, type and size of unit installed.
1.04 QUALITY ASSURANCE
A. Manufacturer: Provide complete, precision built, engineered, pre-fitted unit by a single source manufacturer with at least 20 years experience in providing folding/sliding door systems for large openings in the North American market.
1. The manufacturer must have a quality management system registration to the ISO 9001: 2008 standard.
B. Performance Requirements: Provide from manufacturer that has independently tested typical units. Testing results to include air infiltration in accordance with ASTM E 283 and NFRC 400, water penetration in accordance with ASTM E 547 and E 331, structural loading in accordance with ASTM E 330, and forced entry in accordance with AAMA 1304.
SPECIFIER’S NOTE: Air infiltration and water penetration testing results can only be applicable if the unit matches the test unit in the direction of opening and the type of sill. Structural load testing results are only applicable for the test unit size, type of locking and type of mounting. (Comparative analysis charts published by manufacturer show which panel sizes (if any) would meet structural loading design pressures specifically required for the project. Check for limitations on the use of these charts in the jurisdiction of the project). Forced entry testing results are only applicable for the test unit type of locking. See manufacturer’s latest published data.
C. Thermal Performance U factor: Unit to be rated, certified and labeled in accordance with NFRC 100, shown in manufacturer’s latest published data for the glazing, sill, and direction of opening specified.
D. Solar Heat Gain Coefficient: Unit to be rated, certified and labeled in accordance with NFRC 200, shown in manufacturer’s latest published data for the glazing, sill, and direction of opening specified.
SPECIFIER'S NOTE: If desired, Energy Star ratings can be achieved by the use of proper glass with the unit. See NanaWall's Performance data for details.
E. Installer Qualifications: Installer experienced in the installation of manufacturer’s products or other similar products for large openings. Installer to provide reference list of at least 3 projects of similar scale and complexity successfully completed in the last 3 years.
1.05 WARRANTY
A. Provide manufacturer’s standard warranty against defects in materials and workmanship.
B. Warranty Period: Ten years for rollers and for seal failure of insulated glass supplied. For all other components, one year (two years if unit is installed by manufacturers certified trained installer) from date of delivery by manufacturer.
1.06 SITE CONDITIONS, DELIVERY, STORAGE AND HANDLING
A. In addition to general delivery, storage and handling requirements specified in Section 01600, comply with the following:
1. Deliver materials to job site in sealed, unopened cartons or crates. Protect units from damage. Store material under cover, protected from weather and construction activities.
Part 2 - Products
2.01 SUPPLIER
NANA WALL SYSTEMS, INC.
100 Meadowcreek Drive #250
Corte Madera, CA 94925
Toll Free: (800) 873-5673
Telephone: (415) 383-3148
Fax: (415) 383-0132
Website: www.nanawall.com
Email: info@nanawall.com
2.02 MATERIALS
A. Frame and Panels: From manufacturer’s standard profiles, provide head track, side jambs, and panels with dimensions shown on drawings.
1. Provide panels with:
Standard one lite
[OR with horizontal mullion(s) at specified height(s) from the bottom of the panel]
[OR with simulated divided lites in pattern as shown on drawings].
2. Provide standard bottom rail.
3. Aluminum Extrusion: Extrusions with nominal thickness of .078” (2.0 mm). Alloy specified as AIMgSi0.5 with strength rated as 6063-T5 or F-22 (European standard). Anodized conforming to AAMA 611 or powder coated conforming to AAMA 2604.
4. Thermally broken with a wide Polyamide plastic reinforced with glass fibers. Polyamide plastic less than 7/8 (22 mm) wide or pour and de-bridge thermal break will not be accepted.
5. Aluminum Finish:
Select from NanaWall Powder Coating Finish Chart
[OR clear anodized]
[OR select from range of RAL high gloss powder coated finishes available from manufacturer]
[OR select from range of RAL matte powder coated finished available from manufacturer]
[OR custom finish]
Same [OR different] finishes on inside and outside
B. Glass:
1. All glass to comply with safety glazing requirements of ANSI Z97.1 and CPSC 16CFR 1201. Provide manufacturer’s standard glass with dry glazing:
15/16” (24 mm) insulating clear safety
[OR 15/16” (24 mm) insulating argon filled Low-E safety]
[OR 15/16” (24 mm) insulating krypton filled Heat Mirror TC88 safety]
[OR 1 1/2" (38 mm) triple insulating argon filled Low-E safety]
[OR other glass available from manufacturer, including glass with other total thickness]
2. Provide manufacturer’s standard glass spacers. Provide without capillary tubes [OR with capillary tubes].
C. Locking Hardware and Handles:
1. Main entry panel:
On the main entry panel for models with a pair of swing panels, provide manufacturer’s standard lever handles on the inside and outside, a Schlage compatible lock set with lockable latch, multi-point locking with a dead bolt and rods at the top and bottom on primary panel. Rods to be concealed and not edge mounted. After turn of key or thumbturn, depression of handles withdraws latch. Lifting of handles engages rods and turn of key or thumb turn engages deadbolt and operates lock. On the secondary swing panel, provide matching dummy lever handles on both sides and concealed flush bolts that operate the rods at the top and the bottom for the secondary swing panel.
Stainless steel lever handles in a titanium black finish
[OR stainless steel lever handles in a brushed satin finish]
[OR oil rubbed bronze solid brass lever handles]
[OR satin nickel solid brass lever handles]
[OR white solid brass lever handles]
[OR on the main entry panel for models with a swing panel, provide manufacturer’s standard lever handles on the inside and outside, a Schlage compatible lock set with lockable latch, multi-point locking with a dead bolt and rods at the top and bottom on primary panel only. Rods to be concealed and not edge mounted. After turn of key or thumbturn, depression of handles withdraws latch. Lifting of handles engages rods and turn of key or thumb turn engages dead bolt and operates lock. If there is a secondary swing panel, provide two point locking with flat handles on inside only for the secondary swing panel.
Stainless steel lever handles in a titanium black finish
[OR stainless steel lever handles in a brushed satin finish]
[OR oil rubbed bronze solid brass lever handles]
[OR satin nickel solid brass lever handles]
[OR white solid brass lever handles]
[OR on main entry pair of panels on in swing models without a swing panel, provide manufacturer’s standard L-shaped handle on the inside, flat handle on the outside and lock set with profile cylinder. Operation of lock set is by turn of key from the outside and with a thumbturn from the inside with a two point locking hardware operated by 180º turn of the handle.]
Stainless steel L shaped handles in a titanium black finish
[OR stainless steel L shaped handles in a brushed satin finish]
[OR L shaped handles in a brown nylon finish]
[OR L shaped handles in a gray nylon finish]
[OR L shaped handles in a white nylon finish]
[OR on main entry pair of panels on outswing models without a swing panel, provide manufacturer’s standard flat handle on the inside and on the outside and a lock set with a profile cylinder. Operation of lock set is by turn of key from the outside and from the inside with a two point locking hardware operated by 180º turn of the handle.
SPECIFIER’S NOTE: Key operation from the inside may not meet egress requirements.]
[OR on main entry panel, provide manufacturer’s standard flat handle on inside only with concealed two point locking hardware operated by 180º turn of handle.
SPECIFIER’S NOTE: Note that with this option, the main entry panel is operable from inside only and that there is no latch.]
SPECIFIER’S NOTE: Note that other compatible lever handle styles and finishes are available from other suppliers.]
2. On all other secondary swing panels and pairs of folding panels, provide manufacturer’s standard flat handles and concealed two point locking hardware operated by 180º turn of handle between each pair. Face applied flush bolt locking will not be allowed.
3. Flat Handle Finish:
Stainless steel in a titanium black finish
[OR stainless steel in a brushed satin finish]
[OR closest powder coat match to aluminum profile finish]
Provide handle height centered at 41 3/8” [OR as specified] from bottom of panel.
Aluminum locking rods with fiber glass reinforced polyamide end caps at top and bottom. Rods to have a stroke of 15/16” (24 mm).
If there are more than one unit, keyed alike [OR keyed differently].
D. Sliding/Folding Hardware: Provide manufacturer’s standard combination sliding and folding hardware with top, bottom tracks and threshold. All running carriages to be with sealed, self-lubrication, ball bearing multi-rollers. Surface mounted hinges and running carriages will not be allowed. Weight of panels to be borne by the bottom of the guide channel in the sill will not be allowed.
1. For each pair of folding panels:
For top hung system SL60/o, provide cardanic, independently suspended, four wheeled coated with fiber glass reinforced polyamide upper running carriage and lower guide carriage. Running carriage to be adjustable in height, 1/4" (6 mm) up and down.
[OR for floor mounted system SL60/u, provide upper guide carriage and lower running carriage with two vertical stainless steel wheels and two horizontal wheels. The vertical wheels to ride on stainless steel guide track covers over the full length of sill track and lie above the water run-off level. Carrying capacity of lower running carriage to be 220 lbs. (100 kgs) Wheels rolling below the water run off level and/or riding on aluminum surfaces will not be accepted.]
2. Threshold:
Thermally broken with polyamide raised sill in the same finish as panel finish
[OR clear anodized flush sill]
[OR dark bronze anodized flush sill]
[OR clear anodized thermally broken with polyamide low profile saddle sill]
[OR dark bronze anodized thermally broken with polyamide low profile saddle sill]
[OR clear anodized Surface Mounted Interior Sill (not thermally broken)]
[OR bronze anodized Surface Mounted Interior Sill (not thermally broken)]
A cover plate over the sill will not be allowed.
3. Provide on all four corners of panels, thermally broken, die cast zinc multi-functional corner fittings with carriage connectors, hinges and hinge pins as required. Finish: Powder coated, closest match to finish of frame and panels.
SPECIFIER’S NOTE: Note that as corner connectors are only available in powder coated finishes, if anodized panel and frame finishes are selected, there may be aesthetic issues.
4. Adjustment: Provide system capable of specified amount of adjustments without removing panels from tracks, 5/32” (4 mm) in width per side jamb hinge.
E. Other Components:
1. Weather stripping: Provide manufacturer’s standard double layer EPDM or brush seals with a two layer polyamide fin at both the inner and outer edge of door panels or on frame for sealing between panels and between panel and frame. Single layer weather stripping will not be allowed.
2. Provide tapered pins or machine screws for connecting frame components.
2.03 FABRICATION
A. Use extruded aluminum frame and panel profiles with male-female interlocking, corner connectors and hinges, sliding and folding hardware, locking hardware and handles, glass and glazing and weather stripping as specified herein to make a folding glass wall. Factory pre-assemble as is standard for manufacturer and ship with all components and installation instructions.
B. Sizes and Configurations: See drawings for selected custom dimensions within maximum frame sizes possible as indicated in manufacturer’s literature. See drawings for selected number of panels and configuration. Inward [OR outward] opening unit. On configurations with a pair of swing panels, looking from inside, primary swing panel on the left [OR right].
2.04 ACCESSORIES (Edit for project requirements.)
A. Provide the NanaScreen, a series of vertical, collapsible, pleated screen panels. Provide pleated screen material with floor tracking chain with 1/4” (5 mm) floor track. See drawings for selected number of panels and configuration.
Provide aluminum top track, side jambs, and vertical struts:
White powder coated
[OR clear anodized]
[OR dark bronze anodized]
[OR powder coated select from range of RAL powder coated finishes available from manufacturer].
NanaScreen installation within opening [OR extended beyond opening]
B. Provide other side lites, transoms, corner posts, or single or double doors as per drawings provided.
Part 3 - Execution
3.01 ERECTION
A. Because of the large dimensions involved and the weight and movement of the panels, verify the structural integrity of the header such that the deflection with live load and dead loads is limited to the lesser of L/720 of the span and 1/4 (6 mm). Structural support for lateral loads (both wind load and eccentric load when the panels are stacked open) must be provided. It is recommended that all building dead loads be applied to the header prior to installing the NanaWall. If so and if a reasonable amount of time has been allowed for the effect of this dead load on the header, then only the building’s live load can be used to meet the above requirements of L/720 or 1/4 (6 mm). If not, both the dead and live loads need to be considered.
It is recommended that all building dead loads be applied to the header prior to installing the NanaWall. If so and if a reasonable amount of time has been allowed for the effect of this dead load on the header, then only the building's live load can be used to meet the above requirements of L/720 or 1/4 (6 mm). If not, both the dead and live loads need to be considered.
B. Examine surfaces of openings and verify dimensions; verify rough openings are level, plumb, and square with no unevenness, bowing, or bumps on the floor.
C. Installation of units constitutes acceptance of existing conditions.
3.02 INSTALLATION
A. Install frame in accordance with manufacturer’s recommendations and installation instructions. Properly flash and waterproof around the perimeter of the opening.
B. Installer to provide appropriate anchorage devices and to securely and rigidly fit frame in place, absolutely level, straight, plumb and square. Install frame in proper elevation, plane and location, and in proper alignment with other work.
C. If necessary, provide drain connections from lower track.
D. Install panels, handles and lock set in accordance with manufacturer’s recommendations and installation instructions.
E. If necessary, adjust hardware for proper operation.
F. Accessories: Screens; install in accordance with screen manufacturer’s recommendations and installation instructions.
End of Section
DISCLAIMER
Nana Wall Systems, Inc. takes no responsibility for product selection or application, including, but not limited to, compliance with building codes, safety codes, laws, or fitness for a particular purpose. The guide specifications is not intended to be verbatim as a project specification without appropriate modifications for the specific use intended and the particular requirements of a specific construction project.